Linksys EtherFast PPS1UW Manual do Utilizador

EtherFast®Wireless-Ready USB PrintServerUse this Guide to install:Model No.:PPS1UWUser GuideInstant EtherFast®Series

Instant EtherFast®Series139. The Add Printer Wizard screen will come up at this point. Follow the stan-dard procedure for adding printers under Windo

EtherFast®Wireless-Ready USB PrintServer 16Chapter 5: Bi-Admin: PrintServerManagementThe PrintServer is managed by a utility program called Bi-Admin o

EtherFast®Wireless-Ready USB PrintServer 18Instant EtherFast®Series17Obtaining Device Information:The Device Information IconTo access information abo

EtherFast®Wireless-Ready USB PrintServer 20Instant EtherFast®Series19Exiting Bi-Admin:The Application Exit IconTo exit the Bi-Admin program, just clic

EtherFast®Wireless-Ready USB PrintServer The Bi-Admin program can locate Linksys PrintServers on networks other thanyour own, given your network is ru

23When the ConfigureServer screen appears,enter the PrintServername (in Figure 6-3, theexample is SCA71107).Then enter your pass-word (if you createdo

25Click the Wireless tab to allow you to configure information about thePrintServer. The values on this screen are configured through your InstantWir

27Chapter 7: Advanced PropertiesThe Advanced Properties section of the Web-based Utility is for users who havea thorough understanding of networks and

29Click the Logical Printers tab to view or change the logical printer settings ofthe PrintServer. For each Logical Printer, the following fields are

31Click the SNMP tab to view or change the SNMP settings of the Wireless-Ready PrintServer. The PrintServer supports SNMP (Simple Network Management

COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Instant EtherFast and EtherFast are reg-istered trademarks of Linksys. Micr

33Chapter 8: Internet PrintingProtocol (IPP)IPP (Internet Printing Protocol) is a new standards-based system to allowremote printing from a PC to any

355. Click Save to create the IPP port on your system. You will see a messageconfirming that the port has been created and then Figure 8-2. 6. Perform

37IPP Client Setup for Windows 2000 and XPWindows 2000 and XP have their own IPP Client, and there is no need to installthe supplied IPP Client Softwa

EtherFast®Wireless-Ready USB PrintServer 40Chapter 9:DHCP Support for theEtherFast®Wireless-Ready USBPrintServerTo use DHCP, which assigns non-static

Appendix B: About Bi-DirectionalPrintingNormal printing only sends print signals from a PC to a printer. Bi-direction-al printing, also called bitroni

Appendix D:GlossaryAppleTalk - An Apple Computer networking system that support Apple’s pro-prietary local talk.Bit - A binary digit. The value—0 or 1

Basically, a firewall, working closely with a router, examines each networkpacket to determine whether to forward it toward its destination.Firmware -

NetBEUI (NetBIOS Extended User Interface) - The transport layer forNetBIOS. NetBIOS and NetBEUI were originally part of a single protocolsuite that

If a receiver is not tuned to the right frequency, a spread-spectrum signal lookslike background noise. There are two main alternatives, Direct Sequen

Appendix E:SpecificationsStandards: IEEE 802.3 and 802.3u, USB 1.0 and 1.1, PCMCIA 2.0Protocol: TCP/IP, NetBEUI,AppleTalkPorts: One 10/100 RJ-45 Port,

Table of ContentsChapter 1: Introduction 1The Instant EtherFast® Wireless-Ready USB PrintServer 1Features 1Package Contents 2Chapter 2: Getting to Kn

54Appendix G:Warranty InformationBE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODEFROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING.RETURN REQ

Instant EtherFast®Series55Appendix H:Contact InformationFor help with the installation or operation of this product, contact LinksysTechnical Support

© Copyright 2002 Linksys,All Rights Reserved.http://www.linksys.com

Chapter 1:IntroductionCongratulations on your purchase of the Instant EtherFast®Wireless-ReadyUSB PrintServer, the fastest and easiest way to network

4Chapter 2: Getting to Know theEtherFast®Wireless-Ready USBPrintServerLAN Green. The LAN LED serves two purposes.If the LED is continuously illuminate

EtherFast®Wireless-Ready USB PrintServer 6The PrintServer does not have an ON/OFF power switch. Whenever its poweradapter is plugged into a power sup

1. Insert the Setup Utility CD. A built-in autorun will begin the installation ofthe PrintServer’s Bi-Admin Management Utility, and display Figure 4-1

EtherFast®Wireless-Ready USB PrintServer 101. To begin driver installation, click the Start button, and select Run. TypeD:\Driver\Win9xnt\setup.exe (

EtherFast®Wireless-Ready USB PrintServer 12Instant EtherFast®Series115. Driver installation is now completed, but the Print Driver still needs to bec